Skip to content


Archives for

See all posts in the network tagged with

One Aspect of the 360

No comments

I understand that all buildings, for various reasons, will not get a 360 performed on it during a fire. But, for those that we do get to job around, we need to understand what we are looking for.

I recently spoke with an acting officer and asked him what he was looking for when performing a 360. His answer was "fire."  I asked what else? The answer came, "ways in."  We need to make sure we are taking advantage of the information being made available to us while we are circling the building.

This post is going to focus on some basement indicators.  The pictures shown below are just examples of things you might see when making the round.  Keep in mind that at night you need to take a hand light.  For example, the wood behind the basement windows below may not be noticeable with shining a light in the windows on the way around.

        

We must pay attention to what we are looking for when conduction the 360. As you can see, we may be faced with some very challenging situations.  Not only do we need to be aware during the initial arrival, but the RIT will need this information as well.

As always, follow you own operational guidelines and train hard.

This and other topics will be discussed during one of my presentations at Fire Rescue International 2011.  I am presenting for the Company Officer Development track and hope to see you there.

Jason

Upcoming Radio Show with “Taking it to the Streets”

No comments

Check the upcoming radio show tomorrow night on "Taking it to the Streets" with Chris Naum.  It is sure to be a great show and a good time.  Here is some more information:

 

Please call in with your questions and get involved in the online discussions that always are part of the shows.

Stay safe and keep training hard.

Jason

Ordinary Buildings and Considerations

2 comments

Looking at these pictures shows us a building of ordinary construction.  These are usually older buildings and the building we see is typical of many downtown areas.  This particular building has storefronts on the main level with multi-family units above.

            

 

What are the main characteristics of ordinary construction and how do they relate to fire operations?

What are some problems we face with this type of building in many downtown areas that will cause us concern?

What are the challenges with apparatus placment, not just with this buildling, but with many small, downtown buildings?

What are our challenges in regards to exposures and how do we address them?

 

These are just a few issues we face with this type of building. It is important to be prepared for a fire in this type of occupancy.  It will be challenging, especially late at night when that upstairs is occupied and as you can see, access is not necessarily fast.

Share your thoughts and experiences and as always, train hard and thanks for reading.

Jason

 

The Daily Drill: Part 3-Forcible Entry

1 comment

Here is another great post from my friend Lance Peeples of the Webster Groves Fire Department in St. Louis County.  Thanks Lance and now for some fire-thinking to occur.

 

Review the following videos and answer the questions:

 

 

 

1.  Who is assigned the “Irons” or “Bar” position on your first alarm assignment?

 

2.  List EVERY tool the forcible entry (FE) firefighter (FF) should carry when he dismounts the apparatus for an alarm investigation at a multiple dwelling.

 

3.  Are these tools mounted near the riding position of the FE FF?

 

4.  Who is the FF on your first alarm who is designated to use the axe to drive the halligan while the FE FF holds the halligan in place?  What tools should he or she carry?  Are they mounted immediately adjacent to that riding position for quick access?

 

5.  Will a Rabbit tool (hydraulic forcible entry HFT) work on a door with angle iron shields?

 

6.  How would you defeat an inward opening door with angle iron shields that cover the entire length of the door?  What if another piece of angle iron (or a “U” channel) was attached to the door frame and thus prevented placing the fork of the halligan between the frame and the angle iron attached to the door?

 

7.  Is it acceptable to attack the hinge side of an apartment door in a multiple dwelling?  Why or why not?

 

8.  At multiple dwelling fires is it standard practice in your department to force an adjacent apartment door before forcing the fire apartment door?  What might be an advantage of doing this?

 

 

9.  Will a Rabbit (HFT) tool work on outward opening door?  What does an outward opening door in a multiple dwelling suggest to you?

 

10.  What do bolt heads projecting through a door suggest?

 

11.  Should the fork bevel be against or away from the door?  What are the advantages and disadvantages of each position?

 

12.  Some departments order halligan tools that are longer than the standard 30” length for increased leverage.  What is a serious disadvantage of longer tools?

 

Basic Tactical Considerations

7 comments

This post is just a simple challenge of tactical considerations.  The photos that are posted show a single-family house that had fire venting from the C/D corner when first units arrived.  The first in crews could not make the entire hallway on the first push do to intense heat and smoke.

The smoke was banked almost to the floor even with the fire venting from that corner bedroom.

What are some considerations that must be looked at with this fire?  What would be your next plan of action?  Why ist there so much heat and smoke with the fire venting the exterior?  What is your size up?

Share your thoughts and answers with everyone and use this as discussion with your crew.  

As always, train hard and stay safe,

Jason

The Daily Drill 2: VES

2 comments

Here is a post from a very good friend and very wise fireman, Lance Peeples.  Lance is a firefighter/paramedic with the Webster Groves Fire Department in St. Louis County.  Check it out and give some feed back.

 

Review the following video and consider how YOUR fire department operates when answering the following questions:

 

 

1.  Is VES indicated if PPV is used by your department?  What safety precaution should the operator of a PPV fan perform before starting the fan?

 

2.  Notice how the VES firefighter enters head first.  Very experienced instructors often recommend grasping the window frame with the head and upper body protected by the wall and then entering with the opposite foot.  This permits the firefighter to make an emergency ladder slide if necessary.

What is another advantage of this technique?

 

3.  On your first alarm assignment who is the firefighter assigned the responsibility for VES.  Who is the firefighter that will assist him in this technique?

 

4.  If the assisting firefighter ascends the ladder to orient the searching firefighter how can the ladder be butted?  Does it always need to be butted?  Could a tool be driven into the grounds at the butt of the ladder to prevent it from sliding?

 

5.  Are the tools (hook and halligan) needed for VES mounted near the riding position of the member who is responsible for this function or are they mounted on the other side of the apparatus underneath the water rescue rope and drinking cups?

 

6.  Notice how the roof ladder projects into the window slightly.  However, the ladder is already at a very low angle that could result in the butt kicking out.  Should the ladder tip be removed from the window to allow for easier emergency exit/victim removal or does the angle of the ladder preclude this?  What are possible solutions?

 

7.  Some of the commentators below the video are critical of opening the door upon preparing to leave the room…what say you? 

 

 

 

The “Me” Environment

12 comments

I have to admit that I am a proponent of safety.  I believe in wearing seat belts. I believe in wearing all of your protective gear and equipment. I believe in being healthier.  I believe in doing a 360 and situational awareness.  These are just a few of the safety issues that I believe in.

What I will never understand is a statement that puts us, the firefighters, above the victim that could still be saved.  This is not new but something that I just have to get off of my chest.

I recently wrote an article "Techniques for VES".  The beginning of the article specifically states that two firefighters are always ideal for operating.  With that being said, I understand that there will always be those that disagree with things that I write, and I'm fine with that.  What I am not fine with is the recurring theme of "never" do this and "never" do that.

When I instruct I am very careful about not using "never" and "always." We know that in our business those two words can come back to haunt you.  Although the article was about VES, I know that that is a hot button topic. What prompted the article was a training I attended and questions about the tactic.

The fact is that we train for ideal conditions and we want to always have a 2 in 2 out situation.  But, we know the real world is not always so kind.  Statements like, "Safety of your crew and yourself always come first, no matter what the situation" are troublesome to me.  Where does this leave the people in the burning building or under the debris?

Text books are great and operating in this manner is great. But, what if you are the one checking the windows in the rear and you see a hand on the glass? Your by yourself and your equipped to make a quick grab from the window.  Do you wait for three more people? Or, do you take a calculated risk and perform VES that you have trained for?  I for one am going to do what I can to give that person every opportunity to live.  This falls in the same category of an officer that told his guys to "never" search without a hose line.  Is that really the case?  We know that it's not.

Out of the norm tactics are dangerous, but not necessarily reckless.  There is not nor should there be a "cookie cutter" way of doing things in a figurative sense.  Our job and environments are dynamic. Should we have standards and guidelines based on best practices and methods that have worked for decades? Absolutely!  But, we should not be so entrenched in our own ways as not to perform to what situation we are faced with at the time.  The only way to be able to do that is to train for those situations and in order to train for them you must believe that those situations can happen.

All fire ground activities are best performed in teams.  Is it possible that one firefighter may need to make a save utilizing VES? Yes.  Is it dangerous? Yes.  So, it lends itself that if is is possible, dangerous, and we could be placed in that situation, that we should train for it.

I just don't see our profession and our tactics in a "black and white" world. I see the need to adapt and overcome.  But to do that we must expect these situations and train for them.

Stay safe,

Jason

 

Storage in the Stairs

1 comment

We know the importance of inspections and identifying hazards in the buildings that we serve and respond to.  This is just a simple reminder of one hazard that depending on it's location in the building, can be missed.

Combustible storage under stairs or in the stairwell can cause some serious problems.  Even in sprinklered buildings this is a hazard.

The pictures you seeshows a pile of combustible storage in the stairwell and under the stairs in a hotel.  You can also see that this is in the means of egress area next to the exit door.

 

 

 

 

 

 

 

 

 

 

Smoke from a fire from these combustible materials can make the use of the stairwell almost impossible and access for firefighters difficult.  Occupants are expected to use the stairs during a fire and a large mass of people filling a smoke filled stairwell is disastrous.

This building also is equipped with standpipes in the stairwells, so making that connection would be difficult for fire crews trying to make the connection.

Keep an eye on your buildings and explain this situations to your crews to impress the importance of inspections and mitigating these hazards before they become problems.

Train hard and stay safe.

Jason

Standpipe Crowding

3 comments

We have discussed standpipes in the past, but I think it is worth mentioning again. Standpipes in large and high rise buildings are our water source. It is important to know the location of these devices and to ensure that they are not obstructed.

In addition we need to know and understand if they have pressure reducing devices and how that affects our operations.  Study up on these systems and know how to adapt and trouble shoot the stand pipes in your area.

The picture shown is a stand pipe in a hotel. I went to ice in the hotel I was staying in and this was right next to the ice machine.  I didn't measure it, but this standpipe would be very difficult to connect to. Additionally, if we did get connected with hose only, there would certainly be a kink at the coupling, further reducing our pressure.  

This might be a time when we would try to put an elbow on the connection prior to connecting our hose.  However, I think that with this particular standpipe connection, it would be a stretch just to get the elbow connected as well.

Know your buildings and their systems. Prepare for these types of problems and come up with solutions before you have a fire. Thanks for reading and train hard.

Jason

The Door to Nowhere

4 comments

We have all been taught to control the door. I have watched countless firefighters try to kick in doors, bulldoze their way through them along with every other tactic that does not include a set of irons.  Here is one reason why control in forcing doors is so important.

This door is in a city hall that my son was practicing in. The area that the door is in used to be a balcony that goes all the way around the gym with two doors that lead to the main floor of city hall.  Over the years, as they ran out of space, they began to make office space on that balcony.  

The door is almost always locked and access to this area is likely to be searched during a fire.  The hazard here is obvious, but the lesson for any situations: control.

By using proper forcible entry techniques with a set of tools, you can control the door and be cautious about what is behind it.  A fall from this door could be disasterous. We have to be ever diligent to master the basics.  A lack of basic forcible entry skills could result in a Mayday and RIT situation which makes a hazardous situation even more so.

Be smart, know your area and train hard. Master those basic skills and require it of your crew if your the boss. Stay safe and thanks for reading.

Jason

Engine House Training, LLC

No comments

Engine House Training, LLC is a new training group based in St. Louis, MO. We have been doing training together for a long time and finally decided to do something formal with it.  As much as we like to train, we are great friends and have a blast with what ever we are doing.

The web site and blog site are not fully operational yet, but blogs should be coming in the next day or so.  In the meantime, we have launched our Facebook page and would really like to have you check it out.  We have already posted a great deal of material to the page and some of it you have seen before from this site.  You can also follow us on Twitter.

The primary mission with Engine House Training, LLC is to give firefighters the tools they need to survive each and every call.  Although our curriculum is based on self survival, Mayday, and RIT, we place a heavy emphasis on basic skills that will hopefully keep firefighters from needing to use the techniques that we teach.

Here is a quick list of our instructors and their backgrounds:

 

Jason:
  Jason Hoevelmann is a Deputy Chief with the Sullivan Fire Protection District and a firefighter/paramedic with the Florissant Valley Fire Protection District. He has over 20 years of fire service experience and has been an instructor for the last 15 years. He is Instructor Level II and Officer II. He holds a BS in Fire Service Administration from Eastern Oregon University and presents at FDIC and Fire Rescue International as well as other regional conferences.  He has been published in Fire Engineering magazine and OnScene magaizine and writes a monthly column on FireRescue1.com. He is on Missouri Strike Teams 5 and 3.  He is a board member of the ISFSI, a board of director on the IAFC/FLSS and is on NFPA Technical committees for Fire Officer qualifiations and Fire Service Instructor qualifications.
 
 
Gary Graf:
  Gary is a Battalion Chief/Training Officer with the Pacific Fire Protection District. Gary has been in the fire service for over 20 years. Gary helps coordinates training for Tri County Training, Franklin/Jefferson County Task Force 5 and for MUFTRI.  Gary has specialized in all aspects of rescue and firefighter survival.
 
Dave Konys:
Dave is a Captain with the Sullivan Fire Protection District and has been in the fire service for over 10 years. Dave is a fire service instructor 1 and has taught extensively on firefighter safety and survival.
 
Frank Lipski:
 Frank is a firefighter/paramedic with the Florissant Valley Fire Protection District and has been in the fire service for over 15 years.  Frank holds a Bachelors of Science in Fire Science from Columbia Southern University. Frank specializes in rope rescue and firefighter safety and survival techniques.  He is a member of St. Louis County Task Force 3 and is a Swiftwater Rescue Technician.
 
Andy Seers:
Andy is a Captain/Paramedic with the Creve Coeur Fire Protection and has been in the fire service for the past twenty one years. He holds an Associates Degree in Fire Protection Technology and is a Level I certified fire service instructor by the State of Missouri. He is a member of the St. Louis County Strike Team 3 and the St. Louis Co Hazardous Material Team.  He has been teaching safety and survival training throughout the State of Missouri for the past ten years. 
 
We appreciate your support and hope to have a long relationship in the fire service with all of you.  If there is anything we can do for you, please do not hesitate to ask.
 
In Training,
Jason, Gary, Dave, Andy and Frank

 

How Many Uses Can You Come Up With?

1 comment

It's Sunday and I was just sitting at work and I started thinking about an anchor point that I was taught with webbing. Not having tied it in a while I went out and made sure I remembered how to get it done. Lucky for me my memory is still intact.

The other guys came over and we had a short lesson for it's uses and showed them how to tie it too.  This led into a morning of going over some very simple, but effective, ways to use the webbing that we carry.

Everyone has their own ideas about why they carry a certain length of webbing or rope. But, don't limit yourself to the harnesses and escape systems that utilize webbing. The pieces I keep are for a multitude of "basic" practices that assist me, when needed, in actual firefighting.

We can use them for controlling doors, advancing a large line, searching off of a line and more.  I would like you to all share your webbing stories.  What lengths do you carry? Why? And are there any special tricks you have picked up from some experienced guy in the house?

Take care and remember our troops and their families this Memorial Day.

It’s That Simple

2 comments

    We have all heard the same statement, " the department starts and ends with the company officer."  Whether you agree with this statement or not, we cannot deny the profound affect, both negative and positive,that the company officer has on our companies and ultimately our department.

     How we operate and how we train will be dictated by how the company officer lays out his expectations and how the daily routines are performed.  When a company officer during a training evolution makes a broad statement to his young crew that "we never enter a building without a charged hoseline", we know what the ramifications will be for the members of his company and the people they are supposed to protect.  These attitudes and beliefs will be perpetuated, making our job even more difficult.

   It is easy to see how the long term attitude and beliefs will be affected one way or the other by the example set by the company officer. Lazy company officers have lazy crews and working company officers have working crews. I don't know when this got so complicated.?  

     When the backstep pulls the line off of the rig inadequately and the officer jumps his shit, we have a problem.  Is it not the job of the company officer to make sure his crew is ready?  Is it not the officers job to ensure that the guys on his truck are proficient at the tasks as simple as pulling a line?  Sure the backstepper has a responsibility, but that company officer has a problem with the wrong guy.  If that company officer drilled regularly, any deficiencies would have been identified and remediated before they became a problem. It's called knowing your crew.

    The way that we get to know our crew is to get to know your crew. That means you, as a company officer, have to invest in your people.  You have to "work" with them. That means actually doing things around the fire house and talking. That means eating together and doing regular training drills.  It is a relationship and you have to put "quality" time into it.   You cannot expect to come in, run a few calls and go home and expect to know who your working with.

    In most parts of the country we are fighting less fires.  This is dangerous and makes it even more important to drill regularly.  The officers of the past had years of actual firefighting experience to lean on and pass on. We are losing that experience and that requires us to train as a crew in order to know what is expected, what our company capabilities are based on available resources and to create those "experiences" that are hard to come by.  It all falls on the company officer.

    If you ask most companies and officers, there are a few things that really brings a crew together.  One, obviously is a good, working fire.  Everyone comes back and is pumped up and the stories begin. Second is meaningful training that is inclusive, well planned and relevant.  Third is doing projects in the house.  No matter what the work is, the crew talks, interacts and generally has a good time while doing work together.

    We can't allow our comforts of the job to override the mission. Stay safe and train. Hey, maybe today take off the hand tools and give them a good sanding and cleaning.  Oh, and do it as a crew.

Take care,

Jason 

    

    

What’s Your Take?

1 comment

I spend a lot of time looking at buildings and thinking about "how would I do this or that" and what kinds of challenges would exist should a fire happen.  It drives my wife nuts! You know what I mean? You go to an establishment or an event and you are looking around for exits, sprinklers, fire alarms and just the general layout of the building.

It is good for us to identify these different characteristics on a frequent basis. Even if it isn't in your area, I believe it keeps you sharp. It's like practicing all of the things you have learned in your head.  Granted, you aren't manipulating a tool or pulling a line, but you can do all of those things in your head.  What would you do with this type of door? How about this wierd little addition and the ventilation problems that it poses? These are all considerations you can do any time and any where.

Here a few pictures from a recent trip to Nashivelle, TN.  We were walking back from LP Field after the half-marathon and this building was right next to the pedestrian bridge we were on.  I stopped and started taking pictures and thinking. Of course I got behind and my wife had to explain to everyone else in the group that I was a just a wierd firefighter who does this all of the time.

Take a look and share what you see and all of the different considerations and challenges that could be recognized during a fire in this buillding.

Take care and train hard.

Jason

Common Diseases and Health Problems of Firefighters

No comments

This is an article that was written by a reader. He is passionate about firefighter health and safety and wanted to pass along some information.  We all know that we can always do better when it comes to our own health.  We do a good job of promoting safety to our citizens and community, but neglect the same message for our own safety.

Read the article and pass on the information.  Thanks to Taylor for submitting it.

 

 

Common Diseases and Health Problems of Firefighters

The dangers of firefighting are not always readily apparent.  Obviously, the most visible hazard is the fire itself and the severe damage it causes to the structure the firefighter must enter.  However, even without serious injury, firefighters have a high risk of long-term health problems as a result of their occupation.

Chronic Respiratory Problems & cardiovascular disease

Even if the smoke from a particular fire does not contain any toxic substances, it can still have a detrimental effect on the firefighter’s health.  Smoke and dust inhalation can exacerbate existing heart and lung problems, as well as cause new problems like bronchitis or lung inflammation.  While most fire stations are equipped with self-contained respirators, they are often impractical for lengthy jobs such as wildfires, when 30 minutes of oxygen may not be nearly enough to get the job done.  While treatments such as steroid inhalers can help mitigate the symptoms, more research needs to be done on the long-term effects of smoke and dust inhalation.

No one would argue that firefighting is not a high-stress occupation.  Even the most careful firefighter must deal with extreme stress on a regular basis, and that kind of strain takes a toll on the body.  Chronic stress wears down the body’s immune system, making it more prone to other diseases.  But perhaps the most dangerous aspect of stress is its effect on the heart – hypertension (high blood pressure) is very common among firefighters, and left unchecked, it can lead to stroke, heart attacks, and aneurysms.  Smoke, too, has a detrimental effect on the heart and blood vessels when it prevents the blood from properly delivering oxygen to all systems of the body.  The National Institute for Occupational Health and Safety lists cardiac death as the most common cause of fatality in firefighters.

 

Mesothelioma

Asbestos is widely known as a health hazard.  However, though it is no longer used in the manufacture of new construction materials, it is still commonly found in homes and other buildings constructed before the 1980s.  When intact, asbestos-containing materials pose little danger to the residents, but firefighters most often contend with these materials as they are being destroyed.  Tiny, needle-like asbestos fibers can be inhaled into the lungs, where they can cause serious health problems including symptoms of mesothelioma, an aggressive and extremely deadly cancer of the lining of the chest.  By the time these symptoms appear, the disease has often progressed past the point of treatment. This makes mesothelioma life expectancy extremely severe and short on average.

Other Cancers

Asbestos is not the only toxin released by burning buildings.  Firefighters also have unusually high rates of cancer such as Hodgkin’s lymphoma, multiple melanomas, and testicular and prostate cancer.  Unlike mesothelioma, there is not a known direct link between the particular toxic chemicals and these cancers (for example, we cannot say that chemical X causes cancer Y), but there is no doubt that firefighters come in regular contact with clouds of toxic smoke in the course of their jobs.

The chronic health effects of firefighting have received more press in recent years due to the heroics of the New York Fire Department during and after the collapse of the Twin Towers on 9/11.  Just recently, Congress passed the Zadroga 9/11 Health and Compensation Act to provide health care to those who responded after the terrorist attacks and are still experiencing illness.  Hopefully, both lawmakers and the public alike will continue to remember that the danger to firefighters does not disappear as soon as the fire is out.

Taylor Dardan is an EMS/First Responder Health and Safety Advocate.  He is very passionate about making sure that firefighters and other first responders are properly aware of various hidden dangers surrounding rescue work.

Moving and Flood Water–Be Careful and Prepared

No comments

With the recent storms that are hitting the majority of the country, I wanted to take a minute to ask everyone to take a little extra caution when confronting moving and flood water.

It is important to remember that just because it doesn't look fast doesn't mean it isn't dangerous. Any moving water, no matter how slow it looks is dangerous and should be treated as such.

Some fundamental reminders; Don't drive into flood or moving water.  You have no idea what the conditions of the driving surface are underneath the water. It may be shallow but the power of water can  alter and significantly damage the road surface below the water line.  In some instances that portion of the road could be washed away completely.

Just like a firefighter or responder would not enter the HOT zone in a hazmat and perform technician level tasks, the same should be true with moving water.  There are skills associated with tech level training that others don't have.  The last thing we need is a responder not reading water conditions correctly and getting caught up in a strainer situation or worse.

Wear your appropriate PPE. If anyone is within 10-15 feet of the water, personal floatation devices should be worn.  And they should be worn without bunker gear. This all comes back to training and skills.  Be diligent and take the appropriate precautions.

If you are operating in moving water and units are in boats and in the water, have a back up plan.  In the pictures you will see that we were operating in flood water that is moving with the river.  We sent crews up stream in boats to retrieve a strander boater.  Although we had to wait on the bank, we didn't just sit around.

Put out some throw bags at interval spacing with a few personnel to deploy them.  If a boat capsizes or a person falls into the water we will be prepared to deploy the throw bags.  Make sure your people on the bank and in the boats are wearing floatation devices.

Think ahead of time and have a back up plan.  Use safety equipment and don't operate outside the scope of your training.

Stay safe and like REO says, "Keep riding the storm out!"

 

Jason

Where Goes the Second Line?

No comments

We all know that it is easy to fall into a rut when it comes to training and even operating at what is labeled the "routine" call. Especially for those that are in suburban, mostly bedroom communities.  

If your like most of the country, you pull past the house to get three sides, stretch a pre-connected hand line and make entry into the front door.  Does this sound familiar to anyone?  And, more times than not, this works just fine.

However, sometimes the bigger issue becomes where to take the second line? What apparatus does it come from and what size should it be?  What about the length?

For most single-family, single story homes, line placement becomes mundane and we get a bit complacent.  The second line many times gets pulled from the same rig as the attack line and goes in the same door as the attack line.

Again, I prefer a seconday apparatus for the back up line, but in most house fires the front door is appropriate for the back up line too.  Of course, it all depends on what is taking place and many other variables as well.

One of the biggest problems I see quite often is on two story house fires.  The first line goes to the fire up stairs and the back up line is at the door.  One of the primary concerns is the integrity of those stairs.  That second line needs to go to the stairs to protect the egress for the crew operating on the second floor.

The same has to be done if you have an attack team on the first floor and a search team on the second; a line needs to be deployed to the stairs.  We must protect that  egress point.  In addition, note changing conditions to the search team and the attack team.  Maybe the fire has spread or can't be found by the attack team and your observations are important.

What are your operational guidelines for the back up line?  Share you experiences and thoughts.

As always, stay safe and train hard.

Jason

Basement Rescue Video

4 comments

Here is a great video of some basement removal techniques.   This is another video from Dale Pekel, who looks like he may have gotten a promotion? Dale?  Anyway, these props are able to be used for multiple drills and Dale is very generous with how to build them.

These two techniques are great and you can see that one must be comfortable and well trained in the use of the SCBA. Confidence comes from continued use and training.  You must master the basics and know your tools like the back of your hand.  This allows you to perform the more advanced tasks without worrying about the simple things because they become second nature.

Train hard and stay safe. Thanks Dale for another great video.

 

Jason

Basement Considerations

No comments

With the recent posts about the anniversary of the Colerain-Township LODD from 2008, I thought I would provide some thoughts about basements and some of the things we can do to better prepare.

It recent years it seems we hear a lot about firefighters being killed and injured in residential fires where the basement was involved.  There are a few reasons for this including changing building construction as in the use of engineered i-joists and the heavy fire loads that we have in basements.  In addition, most houses with basements don't just use them for storage anymore. Basements are used as active living spaces increasing activity, heating and electrical demands that were not always present in the past.

One thing that we can do to help prevent some of these issues is to know what we are dealing with.  Probably one of the most important tasks a fire officer can do when arriving on the scene of a residential fire is to complete a 360 walk around of that building.  This gives us information we cannot obtain by darting for the front door.

By seeing all four sides of the fire building we can see if the seat of the fire is in the basement and may allow us a more direct attack from the same level as the fire reducing the chances of floor failure.  We are also able to see hazards that impede our egress if a quick escape is necessary.  It gives us an idea of our options for ventilation and fire control.

The pictures show some of the hazards that we can find and keep mind of during our 360.  Exterior stair wells are altered and secured causing us difficulty making an egress.  This is a perfect time for the first due officer to relay these findings to the next due or the RIT crew.  These other units should cut locks, open bulk heads and make sure the egress points of the basement are accessible.

Additionally, we need to know the characteristics of the buildings in our still area.  This is a picture of a house that is approximately 50 years old and the stairs to the basement are in the garage.  Not knowing this could put our initial attack team at risk by searching the main level while fire is burning under them increasing the chances of a failure.  Some of these homes have no outside exit and we must protect the stairs for the basement crew just like we would for a crew that ascend to a floor above us.

Take some time to look around your area and discuss these issues with your crew.  Prepare your newer members for that thermal layer as you descend the stairs into a basement.  We all know what that first experience is like.  Train hard and don't forget to do that 360, it may just save your life.

Train hard and stay safe,

Jason

Kitchen Suppression Dump Test and Suggestion

4 comments

Some devastating fires have occurred in commercial cooking establishments.  We all know the history of fast food restaurant fires and the toll they can have on a fire department if the fire is not found early.

Kitchen suppression systems are designed to activate to limit the effects of a grease fire in these establishments. It is important to note that when these fires occur and the system is activated, the return air should shut off and the hood vent should activate if it is not already on.

When these systems are designed they are equipment specific. Meaning that the flow points are determined by the type of cooking appliance and its location under the hood and suppression system. Moving or replacing any appliance requires reevaluation of the system and could mean an alteration to keep the system adequate.

As you can see in the picture, the appliance shown has wheels.  This could create a problem in the future when the ownership wants to move things around a bit and could be detrimental to the effectiveness of the system. One suggestion is to adopt a local ordinance that requires these wheels to be removed or locked. I have seen it both ways and it is up to your jurisdiction on how to do that.

Secondly, you want to ensure that the suppression system is hooked into a monitored fire alarm system or on a direct dial alarm system.  We, the fire department, want to know if this system activates.  Even if the system puts the fire out, there is a possibility of fire being pulled into the vent duct. If there are any penetrations or gaps in that duct, fire could smolder above for a long time or it could be burning the uncleaned grease.  We also want to make sure that if that system activates it gets put back in service appropriately and prior to cooking commencing again.

In the video it shows a "dump" test where we make sure that the correct amount of product is being flowed and that all utilities are shut off with the activation.

I know this is not a tactical post, but it gives you a little insight of why these systems are important.  I may not have touched on all of the aspects of these systems, so if you have additional comments or suggestions, please feel free to comment.

Thanks, stay safe and be careful.

Jason

Black Diamond X2 Boots

1 comment

I am late with this review, but it has just been so busy with everything going on this time of year. But, the delay has given me some extra time to really get familiar with the new Black Diamond X2 boots. I mean, I tried these boots in just about every situation you can imagine.

They tout this new gel insert for comfort, so, I took off in them for a little run thinking they would be great for that.

They protect your feet from water and ice, so I used them during some SCUBA training.

I played basketball in them and even tried that new toe cap protection on the soccer field. I just wasn’t getting the feel for them.

Finally, I had the opportunity to wear them for some live burn training at the academy. During these days the instructors are on our feet all day. There is a rotation in and out of the burn tower, but we are active most of the day and these boots were on my feet the entire time, excluding lunch. img_1882img_1883img_1884img_1885

A short time after that, I had the opportunity to wear them at FDIC 2011 for the HOT class that I attended, Truck Company Essentials with Mike Ciampo and the Brotherhood Instructors. Needless to say, I was on my feet all day again.

Having the opportunity to really wear these boots has given me a very strong opinion about them. By far the best pair of structural firefighting boots I have every worn. And that is no BS!

I am going to give it to you straight here from a firefighters perspective.

First, I ordered a size that is the same as my running shoe. They offer three different widths, I am a medium and was more than pleased. The boot feels like a shoe or duty boot with just a little extra space. The boot doesn’t slip, but when I’m on my feet all day or in the summer, my feet swell a little bit and this boot allows for that or for an extra pair of socks in the winter.

Wearing them all day was like wearing a pair of duty boots. Sure, they are a bit larger and bulkier, but they don’t feel like a pair of bricks are tied to you. I was really surprised how light they were. I do a lot of running and I love light shoes, for what they are built for, firefighting, they are extremely easy to wear.

I really liked that they are easy to pull on and off. The large opening allows easy and fast donning and the canvass back does not irritate my calves when I am on my knees or bending. At first they were a bit stiff, but after breaking them in, they are more flexible than other boots I have worn.

Having done instruction for many years, being in any fire boot can be very hard on your feet. I have come away from very long days in my boots only to have really sore feet when it was all over. This makes the training difficult due to being uncomfortable. I can honestly say that these boots did not provide the same results.

Being on my feet for two 8 hour days had absolutely no adverse affects on my feet. They really got it right with the Ortholite Footbed. As I said, I am used to wearing running shoes on a regular basis and I like soft, light shoes. Now don’t get me wrong, these are not running shoes, but they do provide some comfort right where you stand.

I have two cons to admit to. One, the ankle protection is very stiff. Over time this started to loosen up, but at certain times the stiffness of the ankle can cause some irritation, especially on the outer part of the ankle.

The second con would be, like Fire Critic stated, it is made in China. I know in my department there is a strong desire and move to buy only American made products. At times this is difficult at best, not just for fire boots but for all our purchasing needs in regards to station wear and PPE. I don’t know if that is a consideration, but I think it would go a long way in the American fire service.

My general opinion is that these boots are well worth the price tag, which is reasonable. I will continue to wear these boots and would have no problem recommending them to friends and colleagues. However, I would not recommend them for running, soccer, basketball or SCUBA diving. But, they are great for fighting fires and operating on emergency scenes.

I also want to thank Black Diamond Boots for the opportunity to review their product.

As always, train hard, stay safe and wear good boots!

A Firefighter’s Own Worst Enemy @ FDIC 2011

2 comments

I am finally home from the week that was FDIC 2011. It was a great week and I am going to spend a lot of time in the upcoming week going over what I did and sharing my experiences throughout the week.

As some of you may know, I was fortunate enough to present again this year doing “A Firefighter’s Own Worst Enemy” again. The FDIC staff have been wonderful and very accommodating. They always provide a great classroom and assistance for the instructors. It was a true honor, again, to be a part of FDIC 2011 and many thanks to Bobby Halton, Diane Feldman, Mary Jane Dittmar and Ginger Mendolia.

Now, here is a link that Fire Engineering did to highlight my class which is very much appreciated. Check out all of the overviews and comments about FDIC 2011 and keep checking back here this week to see all of the activities from FDIC 2011.

FDIC 2011

1 comment

FDIC 2011

Well, it has been a while since I have posted. It has just been crazy and my time has been in short supply.  As we all know, FDIC 2011 is here.  It starts Monday the 21st of March and I plan on being there the entire week.  I just want to make you aware of some of the things that will be going on at this, the greatest fire training conference in the world.

Of course, Monday and Tuesday are the HOT classes.   The HOT, Hands On Training, classes are the great drills and evolutions that every firefighter dreams of.  These are instructed by the the best instructors that the fire service has to offer. At this time, a great many are sold out, but check the listing and get in any of them, you wont regret it.

Tuesday night is the ISFSI social at Howl at the Moon. This event is for ISFSI members to meet, greet and socialize, and to have few drinks together.  It starts at 6:00PM.  If your not a member, get registered and take advantage of the great resources that the ISFSI offers fire service instructors.

Wednesday the classroom sessions begin and run through the rest of the week.  I am going to ask you to try and check out the list below.  These are people I know or have associations with and I believe that these will be some very worth while presentations.  Some have been highly recommended by others.

Interior Benchmarking
Assistant Chief William M. Greenwood, Fire Emergency Training Consultation Services, Keene, NH
“Interior benchmarks” can help firefighters when they encounter a bad situation in an immediately dangerous to life and health atmosphere. Learn how to recognize these benchmarks and how to employ them so they can help you maintain situational awareness should you become disoriented on the fireground. Interior benchmarking questions are discussed in detail.

ALL LEVELS
Room 107-108

The Ready Position
Engineer Christopher Brennan, Harvey (IL) Fire Department
The Ready Position is the point at which the capacity and capabilities of the Fire Service Warrior are in an ideal state of potential energy. Whether sitting in the firehouse at the kitchen table or in the recliner at home with the pager sitting next to you on the table, ideally, you will be ready to spring into action when an alarm sounds. Learn how to master the physical and mental skills of the Fire Service Warrior: Be 100 percent present when you enter into battle; have the knowledge, skills, and abilities to thrive on the fireground; and be prepared for the unfortunate should the worst-case scenario occur at an incident. ALL LEVELS
Room 234-235

Benefits of the Personal Harness and Escape System
Lieutenant Daniel DiRenzo, Cherry Hill (NJ) Fire Department
The focus is on incorporating these systems with personal protective equipment or self-contained breathing apparatus to rescue other firefighters or self-rescue. Students will become acquainted with the techniques for using this device as well as its capabilities.
ALL LEVELS
Room 103-104

Power Saw Operations and Maintenance Tips
Firefighter Kevin J. Legacy, Fire Department of New York
Students will participate in proactive drills that will ensure safety and promote proficiency when operating saws. They will learn how to troubleshoot minor problems that may arise at the incident scene and that can make the difference between a successful or a failed operation. All aspects of saw maintenance are also addressed. ALL LEVELS
Room 236-237

How to Attack a House Fire
Lieutenant Ray McCormack, Fire Department of New York
A primer for extinguishing house fires according to their locations within the house and customizing the fire attack. Learn when, where, and how to apply your hose stream for maximum effectiveness in single and multiroom fires and fires involving stairways, hallways, attics, lofts, kitchens and bathrooms, basements, and garages. Tips on how to stretch up and down stairways, select the best location for the attack line, and combat fire extension. ADVANCED
Room 140-142

Flat-Roof Operations
Firefighter Nate DeMarse, Fire Department of New York
Attendees are shown a systematic plan of attack that will automatically prioritize the important tasks that must be done when operating on a flat-roof building. The skills needed to safely and efficiently perform primary duties on this type of roof are reviewed.
ALL LEVELS
Room 103-104

Social Media: The Fire Service’s Next Big Innovation
Lieutenant Rhett Fleitz, Roanoke (VA) Fire-EMS Department
Learn the “in’s and out’s” of social media for the fire service. Many questions about these media (blogs, twitter, facebook, MySpace, YouTube, skype, podcasting, text messaging, and so on) will be answered. Learn to be proactive by developing a social media standard operating procedure. Become acquainted with some of the ways departments are using these media for recruitment, retention, informing journalists and citizens, and publishing news. The benefits and potential consequences for personal use of these media by employees are also discussed. ALL LEVELS
Room 134-135

The PIO Reporter: Telling Your Story in a World Where “Spin” Doesn’t Work
Dave Statter, Statter911 Communications, LLC
What you do before an image problem occurs may be more important than what you do later. Building reputation equity in your community could be the key to your survival when things go bad. In this “post-media world,” where the public can access news immediately on the Internet, the fire department can easily lose control of the message. Learn how to communicate so that the public knows what you know, when you know it instead of waiting until all the details are in. Learn how to take control, put out the bad news, build trust with the community, and repair your department’s reputation.
INTERMEDIATE
Room 125-126

Leading with Attitude
Eddie Buchanan, President, International Society of Fire Service Instructors
This class is about empowerment–making positive changes in your department and lives. It poses and answers the questions: What can I do about changing those things I don’t like about my job? Do I have to be a “yes” man to be a good “follower”? How do I deal with the officer, the negative guy, the bobblehead, the rookie—and myself? Participate in a rankless and nameless “gut check” that will reveal what you can do to improve yourself, your department, and the fire service today and for future generations.
ALL LEVELS
Room Lucas Oil Stadium Classroom 2

A Firefighter’s Own Worst Enemy
Deputy Chief Jason Hoevelmann, Sullivan (MO) Fire Protection District
A look at how your actions, behaviors, and attitudes can contribute to your problems and those within your organization if you don’t recognize them and control them, and how supervisors’ human dynamics and interactions in the firehouse can transfer to the fireground. Students will be guided in how to ensure that they and their departments can be a fluid, clear, dynamic moving stream as opposed to a stagnant pond sitting in a farm field. INTERMEDIATE
Room 123-124

Understanding and Motivating Today’s Firefighters
Deputy Fire Coordinator Tiger Schmittendorf, Erie County (NY) Department of Emergency Services
Motivating today’s recruits is the focus. Gain insights that can be applied to all types of departments. Learn how to combat the challenges we face in the firehouse with solutions that are readily apparent. Share in the input from X-Box generation firefighters. Tips for attracting and retaining quality firefighters. ALL LEVELS
Room 105-106

Effective Use of Tower Ladders in Tactical Operations
Firefighter Nicholas A. Martin, District of Columbia Fire Department
Proper use of tower ladders in various fireground scenarios is presented. Topics include proper placement and deployment of aerial apparatus; integrating the aerial into the fireground effectively; and using the aerial in various scenarios such as gaining access, rescues, using elevated master streams, and performing technical rescue. Rear-mount and midmount devices and “ladder tower” vs. “tower ladder” are also discussed.
INTERMEDIATE
Room 238-239

Suburban Fire Tactics
Captain Jim Silvernail, Metro West Fire Protection District, St. Louis County, MO
Strategic principles related to the suburban setting are highlighted. Attendees are motivated to develop and establish effective preferred operating methods for structural firefighting. Students will get a glimpse of “how the rest of the country” is dealing with understaffing and adaptive strategic practices to establish consistent operations.
INTERMEDIATE
Room 120-122

Urban Tactics with Quint Fire Apparatus
Firefighter Nicholas Morgan, St. Louis (MO) Fire Department
The differences of applying standard engine and truck company emergency scene tactics with traditional engine and truck companies only, with all-quint companies only, or with a combination of all three types of fire apparatus are analyzed. The session includes a basic discussion about quints and their similarities and dissimilarities to traditional fire apparatus, the reasons some departments replace older apparatus with quints, and the relative strengths and weaknesses of quint apparatus for standard emergency scene operations.

INTERMEDIATE
Room 120-122

Although I recommend these classes, this is by no means the only people and topics you should go see.  I am just asking that you take the time to come see these great instructors while they are available.

Since this post has gotten a little long I will end it with one more request; please register for the Courage and Valor Run.  This is such an important event and cause. Even if you can’t or don’t want to run, your money for the registration goes to the Courage and Valor Foundation.  If you hurry and register you get really cool t-shirt too.

Well, I hope to see you all at one of the many events that will be taking place. I will be at the ISFSI social and the meet up on Friday.

Travel safe and be careful.  See you in Indy!

Release the Ladder Rack!

2 comments

As with most departments, and mine is no different,  trying to get guys in the habit of throwing ground ladders takes a lot of work.  We know the benefits of doing this and there is a great article in the most current issue of Urban Firefighter Magazine that gives some great direction on how and when to use these valuable tools.

Typically, those throwing the ladders are the firefighters and officers  riding on the trucks and not those that are driving them. There are some exceptions to this rule depending on how your department operates.  In the area that I work, the apparatus driver is tasked with water supply and support.

Any time we have multiple stories we want ladders thrown. Any time we have people on the roof, we want ladders thrown.  It is an important task and one that must be trained on and made a permanent part of your operations.  However, this post is not about the actual act of throwing the ladder, but how we can make this job easier for those that do.

As apparatus drivers when we pull up to the scene of a working fire we are thinking about charging the appropriate line, getting the right gallons per minute to your interior crews and finding a water supply source before the tank water is exhausted.  That is a lot to do and you normally do it all on your own.  Well, there is one more thing I would like you to add to your list.

Depending on what type of configuration you have on your apparatus, the ladders on today’s engines and trucks are not convenient to get to.  We have them on the top of the truck so that they have to be lowered to get to them. They are placed “through the tank” with an access panel on the rear of the apparatus which if you lay line can make them impossible to remove because they are blocked by charged lines coming off of the truck from a rear discharge.  There aren’t many traditional stowed ladder configurations on apparatus anymore.

As operators we have to keep this mind. The photo I have posted shows the lowering arm that the ladders are stowed on.  This arm is lowered for firefighters to gain access. One of the downfalls to this is that the access to compartment space is limited, but not entirely blocked.

Once we get water to our crew and have established a water supply, take a second to check overhead and on the side for obstructions and lower the ladder arm.  If ladders are needed they are ready for deployment and easy to get to.  The RIT crew can use them for preventative measures by throwing ladders to create an egress point for firefighters and rescue teams can use them to make quick access to upper floors for search and rescue.

What about the compartments?  Before you lower the rack, take out the equipment that is most commonly used that must be deployed fast and have it ready to go.  On this particular truck, the PPV fan, the RIT bag and some spare SCBA bottles would be removed prior to lowering the rack.

Get familiar with your ladders and how they are removed. Know what obstacles you might face in placing the ladders in operation based on your apparatus configuration.  Be prepared and train on these facts.

As always, follow your local guidelines for operating on the fireground.  We must continue to train and do the simple things perfect. Master the basics and don’t forget to use your ground ladders.

Who Takes the TIC?

4 comments

In this age of the fire service, most jurisdictions have at least one thermal imaging camera, if not several. Ideally, we would like to have one on every apparatus.  But, of course, budgets and priorities will dictate how many each department feels they can afford and need.

What was once a tool advertised mainly to find victims in building fires, we have found many more uses for this piece of equipment.  It can be used for hazardous materials responses to identify product that may be producing heat.  It can be used to help find a lost person in open space outdoors.  We can use it to check for extension after a small stove fire or for chasing down fire in concealed spaces.

For as many uses as we can name, and I by no means named them all, there are multiple ways that they are deployed.  My preference is for the officer to come off of the truck or engine with the TIC.  Everyone has their own method of operation, but to me the officer makes the most sense.

The officer should be behind the nozzleman and should watching changing conditions at all times.  While doing this, it is easy for him to scan the room or area with the TIC to watch for heat currents, changes in temperatures or victims unseen because of smoke.  These again are not the only things that the officer needs to be doing.

So, the question that I am posing is “Who takes the TIC and how do you deploy it?”  What are your guidelines and how do you operate with it?

In addition, how does it get carried? Do you prefer a strap? Do you carry it in your hand?  Give everyone some input and ideas about what does and has worked for you.

What are some other uses not mentioned and offer some training ideas for the folks here?  Just remember, this is a tool and should  not take the place of masterful search techniques and hard work.

Stay safe and train like you work, hard.